PCEngineFans.com - The PC Engine and TurboGrafx-16 Community Forum

NEC TG-16/TE/TurboDuo => TG/PCE Repair/Mod Discussion => Topic started by: leonk on April 12, 2016, 02:23:59 PM

Title: Turbo Express - Fishy smell !?
Post by: leonk on April 12, 2016, 02:23:59 PM
I recently got a Turbo Express in for a cap kit.  No big deal, remove the old caps, clean all the pads, solder on cap kit I got from console5.  The weird thing is that the "fishy smell" (you all know what that smells like) is still there!

I washed the board pretty damn good with dozens of q-tips and 99 percent alcohol.  The old solder from the pads was removed, and new applied.  The board was super clean before I hit it with the cap kit.

The strangest thing, it's coming from only 1 spot - where the backlight for the LCD plugs in.  I'm wondering, maybe some IC there failing??  The console works great after the cap kit.

Ideas? Suggestions?
Title: Turbo Express - Fishy smell !?
Post by: esteban on April 13, 2016, 01:07:20 AM
(1) Using tweezers, peel your sweaty scrotum off of the TurboExpress.
(2) Pour isopropyl alcohol on your groin/scrotum.
Title: Re: Turbo Express - Fishy smell !?
Post by: leonk on April 13, 2016, 05:16:59 AM
WOW.. the technical level of this thread just went to 0.

Thanks!   :clap:
Title: Re: Turbo Express - Fishy smell !?
Post by: mickcris on April 13, 2016, 08:32:02 AM
There may be some "juice" trapped under an ic. Not sure if a dishwasher would get it. May need an ultrasonic clean.
Title: Re: Turbo Express - Fishy smell !?
Post by: Vimtoman on April 13, 2016, 10:15:29 AM
(1) Using tweezers, peel your sweaty scrotum off of the TurboExpress.
(2) Pour isopropyl alcohol on your groin/scrotum.

Is that from experiance esteban   :D
Title: Re: Turbo Express - Fishy smell !?
Post by: esteban on April 13, 2016, 02:52:40 PM
(1) Using tweezers, peel your sweaty scrotum off of the TurboExpress.
(2) Pour isopropyl alcohol on your groin/scrotum.

Is that from experiance esteban   :D

A resounding "YES, sadly..." is the honest answer.

:)
Title: Re: Turbo Express - Fishy smell !?
Post by: Punch on April 13, 2016, 07:16:13 PM
(1) Using tweezers, peel your sweaty scrotum off of the TurboExpress.
(2) Pour isopropyl alcohol on your groin/scrotum.

Is that from experiance esteban   :D

A resounding "YES, sadly..." is the honest answer.

:)

Good to know that you didn't actually need an ultrasonic clean. Lucky!
Title: Re: Turbo Express - Fishy smell !?
Post by: turbokon on April 14, 2016, 12:28:39 PM
I bet you it taste like chicken(http://s3.amazonaws.com/tapatalk-emoji/emoji12.png)
Title: Re: Turbo Express - Fishy smell !?
Post by: Zero_Gamer on April 15, 2016, 08:58:27 AM
Use some Summers Eve or Vagisil on it. It will be spring fresh in no time.

Sent from my VS985 4G using Tapatalk

Title: Re: Turbo Express - Fishy smell !?
Post by: Zero_Gamer on April 15, 2016, 09:00:58 AM
And yeah... I just turned off the tippity-tappy-talk signature.
Title: Re: Turbo Express - Fishy smell !?
Post by: Reechard on April 23, 2016, 04:20:28 AM
I didn't know where to make my first post in these forums.  Then I read this thread and decided it was time.  I have found my home.
Title: Re: Turbo Express - Fishy smell !?
Post by: esteban on April 23, 2016, 06:22:24 AM
I didn't know where to make my first post in these forums.  Then I read this thread and decided it was time.  I have found my home.

Welcome home, comrade. :)
Title: Re: Turbo Express - Fishy smell !?
Post by: BlueBMW on April 23, 2016, 06:53:33 AM
I'd do a dishwasher cleaning.  My guess is some trapped fluid heating up and stinking.

To wash, use no or minimal detergent gentlest cycle and no heat dry.  When done turn oven on to lowest temp, once heated turn the oven off, put the board inside and leave it for 12 hours.  Reassemble and enjoy.
Title: Re: Turbo Express - Fishy smell !?
Post by: wilykat on April 24, 2016, 12:08:39 PM
Just don't wash the LCD.  They don't like getting wet. Generally the little silver box with LCD panel and backlighting don't stink up.
Title: Re: Turbo Express - Fishy smell !?
Post by: leonk on April 25, 2016, 12:54:07 PM
The unit went back to the customer. After washing down the pcb with 99% alcohol, I wrapped it with dryer sheets and left it sealed in a plastic freezer bag for 12 hours. Smell is gone and customer is super happy. When he initially got it, his entire car stank from it!! :)